Archives

  • 2026-11
  • 2026-10
  • 2026-09
  • 2026-08
  • 2026-07
  • 2026-06
  • 2026-05
  • 2026-04
  • 2026-03
  • 2026-02
  • 2026-01
  • 2025-12
  • 2025-11
  • 2025-10
  • 2025-09
  • 2025-03
  • 2025-02
  • 2025-01
  • 2024-12
  • 2024-11
  • 2024-10
  • 2024-09
  • 2024-08
  • 2024-07
  • 2024-06
  • 2024-05
  • 2024-04
  • 2024-03
  • 2024-02
  • 2024-01
  • 2023-12
  • 2023-11
  • 2023-10
  • 2023-09
  • 2023-08
  • 2023-07
  • 2023-06
  • 2023-05
  • 2023-04
  • 2023-03
  • 2023-02
  • 2023-01
  • 2022-12
  • 2022-11
  • 2022-10
  • 2022-09
  • 2022-08
  • 2022-07
  • 2022-06
  • 2022-05
  • 2022-04
  • 2022-03
  • 2022-02
  • 2022-01
  • Cy7 NHS Ester: Protocols for Near-Infrared Biomolecule Label

    2026-05-29

    Cy7 NHS Ester: Technical Guidance for Reliable NIR Biomolecule Labeling

    What This Product Solves

    Labeling biomolecules with fluorescent probes for sensitive detection is a routine requirement in protein, peptide, and live cell imaging workflows. Many standard near-infrared dyes suffer from poor aqueous solubility and can induce aggregation or denaturation of delicate proteins, especially when organic co-solvents are necessary. Cy7 NHS ester (sulfo-Cy7 NHS ester) addresses these challenges by incorporating sulfonate groups, which markedly enhance water solubility and minimize dye-dye fluorescence quenching. This molecular design enables direct labeling of amino groups in biomolecules—even those sensitive to denaturation—without organic solvents. Its near-infrared excitation (750 nm) and emission (773 nm) maximize tissue transparency and minimize background autofluorescence, making it a practical near-infrared dye for bioimaging in both purified samples and live organisms.

    Protocol Parameters

    • Assay: Dye–protein conjugation buffer | Value: 50 mM sodium phosphate, pH 7.5–8.5 | Applicability: Suitable for NHS ester labeling reactions | Rationale: NHS esters require mildly basic pH for efficient amine coupling; buffers outside this range may reduce labeling efficiency | Source type: Workflow recommendation
    • Assay: Dye solubility | Value: Fully soluble in water, DMF, DMSO | Applicability: Enables aqueous labeling of proteins and peptides without co-solvents | Rationale: Sulfonate groups confer high water solubility, reducing the risk of protein denaturation | Source type: product information
    • Assay: Storage conditions | Value: -20°C, protected from light, up to 24 months | Applicability: Ensures dye stability and prevents degradation | Rationale: Prolonged light exposure and higher temperatures can lead to decomposition or reduced reactivity | Source type: product information
    • Assay: Dye–protein molar ratio | Value: 3–10:1 (dye:protein) | Applicability: Typical initial range for optimizing labeling density; actual value may need empirical tuning | Rationale: Excess dye ensures efficient labeling, but over-labeling can impact protein function | Source type: Workflow recommendation
    • Assay: Maximum storage of dye solutions | Value: Use immediately; avoid long-term storage | Applicability: Dye solutions are prone to hydrolysis and loss of reactivity | Rationale: NHS esters hydrolyze in aqueous solution, reducing conjugation efficiency over time | Source type: product information

    Workflow Setup and QC Checklist

    • Confirm protein or peptide is free of primary amine-containing buffers (e.g., avoid Tris, glycine); use phosphate or bicarbonate buffers at pH 7.5–8.5.
    • Dissolve Cy7 NHS ester immediately before use; prepare stock in water, DMF, or DMSO as appropriate for your system and use within minutes.
    • Mix dye and biomolecule at the chosen molar ratio (start with 5:1 to 10:1), incubate at room temperature for 30–60 minutes in the dark.
    • Quench unreacted NHS ester with an excess of ethanolamine or similar primary amine after conjugation.
    • Purge excess dye by desalting columns or dialysis before downstream applications.
    • Verify labeling success by absorbance at 750 nm (ε = 240,600 M⁻¹cm⁻¹) and, if necessary, SDS-PAGE with NIR fluorescence imaging.
    • Assess functional integrity of labeled protein, especially for enzymes or antibodies, to ensure labeling did not impair activity.
    • Store labeled biomolecules at 4°C in the dark and avoid repeated freeze–thaw cycles.

    Common Failure Modes and Fixes

    • Low labeling efficiency: Check buffer composition and pH; avoid amine-containing buffers and ensure pH is between 7.5 and 8.5. Prepare dye solution freshly to prevent hydrolysis.
    • Protein precipitation or loss of activity: Reduce dye:protein ratio or perform labeling at lower temperature. Verify protein concentration and buffer compatibility before conjugation.
    • High background fluorescence after purification: Increase the number of wash steps or use higher-resolution desalting columns to remove unbound dye.
    • Rapid loss of dye reactivity: Protect dye from light and moisture; keep dye aliquots frozen and minimize freeze–thaw events.
    • Nonspecific labeling in complex samples: Increase quenching agent after conjugation and optimize purification to remove excess or hydrolyzed dye.

    Scope and Limitations

    Cy7 NHS ester is a robust option for labeling purified proteins, peptides, and other amine-containing biomolecules in aqueous environments. Its sulfonated structure minimizes the need for organic solvents, supporting protocols where protein integrity is sensitive to denaturation. However, it is not suitable for labeling targets lacking accessible primary amines, or in workflows using incompatible buffer systems (e.g., Tris, glycine). NHS esters are also sensitive to hydrolysis and must be used promptly after dissolution; long-term storage of dye solutions is discouraged. For applications that require repeated or prolonged exposure to light, alternative dyes with higher photostability may be warranted.

    For detailed mechanistic applications and advanced workflow strategies, see this guide on advanced protein labeling and NIR imaging and this article on applications in biomolecule conjugation and live tissue imaging. Both explore the practical implications of using sulfo-Cy7 NHS ester in sensitive experimental contexts.

    Conclusion

    Cy7 NHS ester (APExBIO SKU A8109) is a specialized, water-soluble near-infrared dye for bioimaging, designed to enable efficient and gentle labeling of proteins and peptides via NHS chemistry. When protocols are followed with attention to buffer compatibility, dye handling, and purification, this reagent supports reliable, high-contrast imaging in both in vitro and in vivo models. For further details, refer to the product page.